Thursday, October 7, 2010

Node Movement and Topology Generation

To simulate a mobility scenario, the nodes' positions at every time instant need to be determined.


Instead of specifying and controlling each nodes' position and movement pattern, we may use a CMU tool "setdest" to generate large number of nodes and there movements. The tool use a random waypoint model.
Setdest
Setdest tool is used to generate the positions of nodes and their moving speed and moving directions.
The syntax is:

 setdest -v 1 -n $numnodes -p $pt -M $maxspeed -t $simtime -x $maxx -y $maxy
for example: 

    setdest -v 1 -n 50 -p 0 -M 20 -t 900 -x 1500 -y 300
will generate a 1500*300 topology with 50 nodes random distributed labeled by a XY(Z) coordinates.  

(Note that, there is a bug in the README file, which gives a wrong option for specifying the speed, we should use "-M" instead of "-s" ).
In the output, you can find that: after the initial positions are given, the nodes are specified with their movement destination and speed. Then, the initial distance (hop counts) information are counted by a GOD. 
Currently, the god object is used only to store an array of the shortest number of hops required to reach from one node to an other. The god object does not calculate this on the fly during simulation runs, since it can be quite time consuming. The information is loaded into the god object from the movement pattern file (this file)..
Then, the nodes are going to move during this 900-second simulation scenario. During this, the distance (hop-counts) information is going to change, thus, the following lines are going to show this recent change. Note that the distance is calculated based on a nominal radio range as "250" meters. The god information should not be available to any of the node. Thus, for a routing protocol, it has to discover the distance by itself with some mechanism.
It's possible that a node reaches its destination before the simulation timer ends. Thus, it needs to re-specify a new direction and speed for it. Also, the average pause time is a parameter to allow a node stop to move in a destination before moving again.
Finally, there are some statistics about this movement file? During the simulation, some nodes get isolated from all other nodes which results one count of "destination unreachable". Also, all route changes and link changes are calculated.
# nodes: 50, pause: 0.00, max speed: 20.00, max x: 1500.00, max y: 300.00
#
$node_(0) set X_ 1472.239335818631
$node_(0) set Y_ 218.102475038104
$node_(0) set Z_ 0.000000000000
$node_(1) set X_ 266.329091949493
$node_(1) set Y_ 188.988756134562
$node_(1) set Z_ 0.000000000000
.....
$ns_ at 0.000000000000 "$node_(0) setdest 298.258250355189 34.553480936942 5.763540789209"
$ns_ at 0.000000000000 "$node_(1) setdest 783.793876303622 280.181784294036 16.832727003192"
$ns_ at 0.000000000000 "$node_(2) setdest 978.836090908830 151.467060345492 19.354908025316"
$ns_ at 0.000000000000 "$node_(3) setdest 376.126888262665 139.747808400435 11.497476206039"
$ns_ at 0.000000000000 "$node_(4) setdest 370.541780738321 185.032792269909 8.002013555825"
$ns_ at 0.000000000000 "$node_(5) setdest 1463.652810766312 132.618506062927 17.607998988233"
$ns_ at 0.000000000000 "$node_(6) setdest 1020.046295404814 40.982731716802 15.434148765705"
......
$god_ set-dist 0 1 6
$god_ set-dist 0 2 1
$god_ set-dist 0 3 4
$god_ set-dist 0 4 2
$god_ set-dist 0 5 4
$god_ set-dist 0 6 8
$god_ set-dist 0 7 6
......
$ns_ at 0.141920608238 "$god_ set-dist 17 24 2"
$ns_ at 0.165720133690 "$god_ set-dist 3 15 1" 
$ns_ at 0.263269271549 "$god_ set-dist 1 46 2" 
$ns_ at 0.263269271549 "$god_ set-dist 7 46 2" 
$ns_ at 0.263269271549 "$god_ set-dist 12 46 1"
$ns_ at 0.263269271549 "$god_ set-dist 25 46 3"
$ns_ at 0.263269271549 "$god_ set-dist 46 47 3"
$ns_ at 0.314230786054 "$god_ set-dist 5 42 5" 
......
$ns_ at 12.602131706040 "$god_ set-dist 16 36 2"
$ns_ at 12.623221733243 "$node_(12) setdest 424.679916546080 186.581540202946 5.803287072825"
$ns_ at 12.682532746855 "$god_ set-dist 18 40 3"
.....
$ns_ at 899.907548331028 "$god_ set-dist 32 40 1"
$ns_ at 899.932142983319 "$god_ set-dist 22 40 1"
$ns_ at 899.991403308054 "$god_ set-dist 3 29 1"
#
# Destination Unreachables: 429
#
# Route Changes: 72037
#
# Link Changes: 11892
#
# Node | Route Changes | Link Changes
# 0 | 2709 | 433
# 1 | 3098 | 467
# 2 | 2651 | 496
# 3 | 3398 | 642Setdest
# 4 | 3036 | 548
# 5 | 2755 | 252
# 6 | 3471 | 601
for generate scenarios in a patch, we could use following shell scripts.
#!/bin/csh
unset noclobber
set outdir = wzb-scen

set maxspeed = 1
set numnodes = 50
set maxx = 1500
set maxy = 300
set simtime = 900

foreach pt (5 10 15 20 25 30 40 50)
foreach scen ( 1 2 3 4 5)
echo scen $scen : setdest -n $numnodes -p $pt -M $maxspeed -t $simtime \
      -x $maxx -y $maxy
time ./setdest -n $numnodes -p $pt -M $maxspeed -t $simtime \
      -x $maxx -y $maxy \
      >$outdir/scen-${maxx}x${maxy}-${numnodes}-${pt}-${maxspeed}-${scen}
echo
end
end

Simulating wireless link errors

To attach the error model, add following codes to a TCL simulation script


..........
proc UniformErr {} {
                set err [new ErrorModel]
                $err unit packet
                $err set rate_ 0.05
                return $err
        }
        # $err rate_ 0.5  "invalid command ErrModel::Command does not support"
        # the other valid method is " set err [new ErrorModel/Uniform 0.05 pkt] "
        # the parameter rate ( 0 or 0.9) is a threshold that all packets all going through and 90% packets are
        # going to be drop

     proc TwoStateMarkovErr {} {

                set tmp0 [new ErrorModel/Uniform 0 pkt]
                set tmp1 [new ErrorModel/Uniform .7 pkt]

                 # Array of states (error models)
                set m_states [list $tmp0 $tmp1]
                 # Durations for each of the states, tmp, tmp1 and tmp2, respectively
                set m_periods [list 0.1 .075 ]
        # Transition state model matrix
        set m_transmx { {0.9   0.1 }
                        {0.7   0.3 } }
        set m_trunit byte
        # Use time-based transition
        set m_sttype time
        set m_nstates 2
        set m_nstart [lindex $m_states 0]

        set em [new ErrorModel/MultiState $m_states $m_periods $m_transmx \
                $m_trunit $m_sttype $m_nstates $m_nstart]
        return $em
    }

      $ns_ node-config -adhocRouting $val(rp) \
                         -llType $val(ll) \
                         -macType $val(mac) \
                         -ifqType $val(ifq) \
                         -ifqLen $val(ifqlen) \
                         -antType $val(ant) \
                         -propType $val(prop) \
                         -phyType $val(netif) \
                         -channel  $chan1 \
                         -topoInstance $topo \
                         -agentTrace ON \
                         -routerTrace OFF\
                         -macTrace ON \
                         -movementTrace OFF \
                         -IncomingErrProc TwoStateMarkovErr
                         #\
                         #-OutcomingErrProc TwoStateMarkovErr

#The other way to configure error
#        $ns_ node-config --IncomingErrProc $opt(err)

Network Simulator 2 script for a complex scenario


#This is an example for DSDV routing with 50 nodes in a 670*670 m2 area
#
# Note that all options listed in the beginning of the file could be initialized 
# with command line arguments by using "getopt $argc $argv"
# ======================================================================
# Default Script Options
# ======================================================================
set opt(chan)  Channel/WirelessChannel
set opt(prop)  Propagation/TwoRayGround
#set opt(netif)  NetIf/SharedMedia
set opt(netif)  Phy/WirelessPhy
#set opt(mac)  Mac/802_11
set opt(mac)  Mac/802_11
set opt(ifq)  Queue/DropTail/PriQueue
set opt(ll)  LL
set opt(ant)            Antenna/OmniAntenna

set opt(x)  670 ;# X dimension of the topography
set opt(y)  670  ;# Y dimension of the topography
set opt(cp)  "../mobility/scene/cbr-50-10-4-512"
set opt(sc)  "../mobility/scene/scen-670x670-50-600-20-0"

set opt(ifqlen)  50  ;# max packet in ifq
set opt(nn)  50  ;# number of nodes
set opt(seed)  0.0
set opt(stop)  1000.0  ;# simulation time
set opt(tr)  out.tr  ;# trace file
set opt(rp)             dsdv            ;# routing protocol script
set opt(lm)             "off"           ;# log movement

# ======================================================================

#set AgentTrace   ON
#set RouterTrace  ON
#set MacTrace   OFF     #useless code, the only way to toggle Mac trace on is to use node-config

LL set mindelay_  50us
LL set delay_   25us
LL set bandwidth_  0 ;# not used
LL set off_prune_  0 ;# not used
LL set off_CtrMcast_  0 ;# not used

Agent/Null set sport_  0
Agent/Null set dport_  0

Agent/CBR set sport_  0
Agent/CBR set dport_  0

Agent/TCPSink set sport_ 0
Agent/TCPSink set dport_ 0

Agent/TCP set sport_  0
Agent/TCP set dport_  0
Agent/TCP set packetSize_ 1460

Queue/DropTail/PriQueue set Prefer_Routing_Protocols    1

# unity gain, omni-directional antennas
# set up the antennas to be centered in the node and 1.5 meters above it
Antenna/OmniAntenna set X_ 0
Antenna/OmniAntenna set Y_ 0
Antenna/OmniAntenna set Z_ 1.5
Antenna/OmniAntenna set Gt_ 1.0
Antenna/OmniAntenna set Gr_ 1.0

# Initialize the SharedMedia interface with parameters to make
# it work like the 914MHz Lucent WaveLAN DSSS radio interface
Phy/WirelessPhy set CPThresh_ 10.0
Phy/WirelessPhy set CSThresh_ 1.559e-11
Phy/WirelessPhy set RXThresh_ 3.652e-10
Phy/WirelessPhy set Rb_ 2*1e6
Phy/WirelessPhy set Pt_ 0.2818
Phy/WirelessPhy set freq_ 914e+6 
Phy/WirelessPhy set L_ 1.0

# ======================================================================

proc usage { argv0 }  {
 puts "Usage: $argv0"
 puts "\tmandatory arguments:"
 puts "\t\t\[-x MAXX\] \[-y MAXY\]"
 puts "\toptional arguments:"
 puts "\t\t\[-cp conn pattern\] \[-sc scenario\] \[-nn nodes\]"
 puts "\t\t\[-seed seed\] \[-stop sec\] \[-tr tracefile\]\n"
}


proc getopt {argc argv} {
 global opt
 lappend optlist cp nn seed sc stop tr x y

 for {set i 0} {$i < $argc} {incr i} {
  set arg [lindex $argv $i]
  if {[string range $arg 0 0] != "-"} continue

  set name [string range $arg 1 end]
  set opt($name) [lindex $argv [expr $i+1]]
 }
}

proc cmu-trace { ttype atype node } {
 global ns_ tracefd

 if { $tracefd == "" } {
  return ""
 }
 set T [new CMUTrace/$ttype $atype]
 $T target [$ns_ set nullAgent_]
 $T attach $tracefd
        $T set src_ [$node id]

        $T node $node

 return $T
}




proc log-movement {} {
    global logtimer ns_ ns

    set ns $ns_
    source ../mobility/timer.tcl
    Class LogTimer -superclass Timer
    LogTimer instproc timeout {} {
 global opt node_;
 for {set i 0} {$i < $opt(nn)} {incr i} {
     $node_($i) log-movement
 }
 $self sched 0.1
    }

    set logtimer [new LogTimer]
    $logtimer sched 0.1
}

# ======================================================================
# Main Program
# ======================================================================
getopt $argc $argv

#
# Source External TCL Scripts
#
#source ../lib/ns-mobilenode.tcl

#if { $opt(rp) != "" } {
 #source ../mobility/$opt(rp).tcl
 #} elseif { [catch { set env(NS_PROTO_SCRIPT) } ] == 1 } {
 #puts "\nenvironment variable NS_PROTO_SCRIPT not set!\n"
 #exit
#} else {
 #puts "\n*** using script $env(NS_PROTO_SCRIPT)\n\n";
        #source $env(NS_PROTO_SCRIPT)
#}
#source ../lib/ns-cmutrace.tcl
source ../lib/ns-bsnode.tcl
source ../mobility/com.tcl

# do the get opt again incase the routing protocol file added some more
# options to look for
getopt $argc $argv

if { $opt(x) == 0 || $opt(y) == 0 } {
 usage $argv0
 exit 1
}

if {$opt(seed) > 0} {
 puts "Seeding Random number generator with $opt(seed)\n"
 ns-random $opt(seed)
}

#
# Initialize Global Variables
#
set ns_  [new Simulator]
set chan [new $opt(chan)]
set prop [new $opt(prop)]
set topo [new Topography]
set tracefd [open $opt(tr) w]

$topo load_flatgrid $opt(x) $opt(y)

$prop topography $topo

#
# Create God
#
create-god $opt(nn)


#
# log the mobile nodes movements if desired
#
if { $opt(lm) == "on" } {
    log-movement
}

 $ns_ node-config -macTrace ON


#
#  Create the specified number of nodes $opt(nn) and "attach" them
#  the channel.
#  Each routing protocol script is expected to have defined a proc
#  create-mobile-node that builds a mobile node and inserts it into the
#  array global $node_($i)
#

if { [string compare $opt(rp) "dsr"] == 0} { 
 for {set i 0} {$i < $opt(nn) } {incr i} {
  dsr-create-mobile-node $i
 }
} elseif { [string compare $opt(rp) "dsdv"] == 0} { 
 for {set i 0} {$i < $opt(nn) } {incr i} {
  dsdv-create-mobile-node $i
 }
}



#
# Source the Connection and Movement scripts
#
if { $opt(cp) == "" } {
 puts "*** NOTE: no connection pattern specified."
        set opt(cp) "none"
} else {
 puts "Loading connection pattern..."
 source $opt(cp)
}


#
# Tell all the nodes when the simulation ends
#
for {set i 0} {$i < $opt(nn) } {incr i} {
    $ns_ at $opt(stop).000000001 "$node_($i) reset";
}
$ns_ at $opt(stop).00000001 "puts \"NS EXITING...\" ; $ns_ halt"


if { $opt(sc) == "" } {
 puts "*** NOTE: no scenario file specified."
        set opt(sc) "none"
} else {
 puts "Loading scenario file..."
 source $opt(sc)
 puts "Load complete..."
}

puts $tracefd "M 0.0 nn $opt(nn) x $opt(x) y $opt(y) rp $opt(rp)"
puts $tracefd "M 0.0 sc $opt(sc) cp $opt(cp) seed $opt(seed)"
puts $tracefd "M 0.0 prop $opt(prop) ant $opt(ant)"

puts "Starting Simulation..."
$ns_ run

A simple example for wireless simulation scenario


#This script creates a 4x4 grid topology and run 4 CBR traffic flows over four pair of#nodes in this grid.
# ===================================================
# Author: ZHIBIN WU 06/19/2003
# ==================================================



set cbr_size 500
set cbr_interval 0.002
set num_row 4
set time_duration 100

set val(chan) Channel/WirelessChannel ;# channel type
set val(prop) Propagation/TwoRayGround ;# radio-propagation model
set val(netif) Phy/WirelessPhy ;# network interface type
set val(mac) Mac/802_11 ;# MAC type
set val(ifq) Queue/DropTail/PriQueue ;# interface queue type
set val(ll) LL ;# link layer type
set val(ant) Antenna/OmniAntenna ;# antenna model
set val(ifqlen) 50 ;# max packet in ifq
set val(rp) DSDV ;# routing protocol
# 
# Initialize ns
#
set ns_ [new Simulator]
set tracefd [open simple.tr w]
$ns_ trace-all $tracefd

# set up topography object
set topo       [new Topography]
$topo load_flatgrid 1000 1000

create-god [expr $num_row * $num_row ]

$ns_ node-config -adhocRouting $val(rp) -llType $val(ll) \
     -macType $val(mac)  -ifqType $val(ifq) \
     -ifqLen $val(ifqlen) -antType $val(ant) \
     -propType $val(prop) -phyType $val(netif) \
     -channel  [new $val(chan)] -topoInstance $topo \
     -agentTrace ON -routerTrace OFF\
     -macTrace ON \
     -movementTrace OFF
 
for {set i 0} {$i < [expr $num_row*$num_row]} {incr i} {
    set node_($i) [$ns_ node]
}
set k 0;
while {$k < $num_row } {
    for {set i 0} {$i < $num_row } {incr i} {
 set m [expr $i+$k*$num_row];
 $node_($m) set X_ [expr $i*240];
 $node_($m) set Y_ [expr $k*240+20.0];
 $node_($m) set Z_ 0.0
    }
    incr k;
}; 
for {set i 0} {$i < $num_row } {incr i} {
    set udp_($i) [new Agent/UDP]
    set null_($i) [new Agent/Null]
} 
  $ns_ attach-agent $node_(0) $udp_(0)
  $ns_ attach-agent $node_(7) $udp_(1)
  $ns_ attach-agent $node_(2) $udp_(2)
  $ns_ attach-agent $node_(7) $udp_(3)
  $ns_ attach-agent $node_(6) $null_(0)
  $ns_ attach-agent $node_(1) $null_(1)
  $ns_ attach-agent $node_(8) $null_(2)
  $ns_ attach-agent $node_(15) $null_(3)
for {set i 0} {$i < $num_row } {incr i} {
     $ns_ connect $udp_($i) $null_($i)
}
for {set i 0} {$i < $num_row } {incr i} {
    set cbr_($i) [new Application/Traffic/CBR]
$cbr_($i) set packetSize_ $cbr_size
$cbr_($i) set interval_ 0.5
$cbr_($i) attach-agent $udp_($i)
} 
$ns_ at 11.0234 "$cbr_(0) start"
$ns_ at 10.4578 "$cbr_(1) start" 
$ns_ at 12.7184 "$cbr_(2) start"
$ns_ at 12.2456 "$cbr_(3) start" 
# Tell nodes when the simulation ends
#
for {set i 0} {$i < [expr $num_row*$num_row] } {incr i} {
    $ns_ at [expr $time_duration +10.0] "$node_($i) reset";
}
$ns_ at [expr $time_duration +10.0] "finish"
$ns_ at [expr $time_duration +10.01] "puts \"NS Exiting...\"; $ns_ halt"

proc finish {} {
global ns_ tracefd
$ns_ flush-trace
close $tracefd
}

puts "Starting Simulation..."
$ns_ run 

Debugging ns-2

Enable gdb debugging
./configure --enable-debug
make clean
make
 
Note: After you have done that, the Makefile is initialized again and loose all your changes to Makefile if your did some.


When ns-2 crashes, here are some possible places to check for any causes of errors:
  1. Scheduler: Event UID not valid!. This is probably associated with timers. If a timer has been called to start again before it expires...
  2. Segmentation fault. A pointer goes to a wrong place. A pointer is out of bound. Or null pointer value.
  3. No obvious cause of fault. Program stopped in a place that no obvious coding errors can be found. Try "make clean + make". Sometimes, if *.h file is changed, the cross-included header files needs to be re-compiled into the final program.
Refer to another article: http://wmlab.csie.ncu.edu.tw/~youngway/MTdata/archives/000104.html

Install ns 2.28 in Debian with gcc 4.0 or above

A usual problem is TK8.4.5 compile failure. This is because of lack of  X11 development libraries. Do apt-get install libx11-dev,libxt-dev
For gcc 4.0.3, ns-2.28 source codes are violating programming regulations. So, some files have to be manually modified to let "make" succeed.
Generally, the declaration of  "class A" has to be put before a reference appears in another class definition. For example,
class B
{

   A*  aa;
....
}

Also, declaration as
static const double ALPHA_ = 0.4;
in a header file, is illegal, because initialization of a static variable in header file would lead to multiple initializations occurred in all files including this header file.

So, it must be changed as :
static const double ALPHA_ // in header file
const double XCPQueue::ALPHA_ = 0.4; // in cpp file
A list of paths are given as below: (copying from ns-mail list)

diff -ru ns-allinone-2.28.orig/nam-1.11/agent.h ns-allinone-2.28/nam-1.11/agent.h
--- ns-allinone-2.28.orig/nam-1.11/agent.h 2001-06-15 21:53:10.000000000 -0400
+++ ns-allinone-2.28/nam-1.11/agent.h 2005-06-13 18:10:05.000000000 -0400
@@ -70,7 +70,7 @@
 inline double width() {return width_;}
 inline double height() {return height_;}
 virtual void findClosestCornertoPoint(double x, double y, 
- double &corner_x, double &corner_y) const = NULL; 
+ double &corner_x, double &corner_y) const = 0; 
 virtual void place(double x, double y);
 void label(const char* name, int anchor);
 void color(const char* name);
diff -ru ns-allinone-2.28.orig/ns-2.28/diffusion3/lib/nr/nr.hh ns-allinone-2.28/ns-2.28/diffusion3/lib/nr/nr.hh
--- ns-allinone-2.28.orig/ns-2.28/diffusion3/lib/nr/nr.hh 2005-01-19 13:23:21.000000000 -0500
+++ ns-allinone-2.28/ns-2.28/diffusion3/lib/nr/nr.hh 2005-06-13 18:11:03.000000000 -0400
@@ -43,7 +43,8 @@
 typedef signed int int32_t;
 #endif
 typedef signed short int16_t;
-#if defined (sparc)
+// #if defined (sparc)
+#if defined (__SVR4) && defined (__sun)
 typedef char int8_t;
 #else
 // Conflicts with system declaration of int8_t in Solaris
diff -ru ns-allinone-2.28.orig/ns-2.28/xcp/xcpq.cc ns-allinone-2.28/ns-2.28/xcp/xcpq.cc
--- ns-allinone-2.28.orig/ns-2.28/xcp/xcpq.cc 2005-02-03 13:29:20.000000000 -0500
+++ ns-allinone-2.28/ns-2.28/xcp/xcpq.cc 2005-06-13 18:10:30.000000000 -0400
@@ -33,6 +33,15 @@
 } class_droptail_xcpq;
 
 
+const double XCPQueue::ALPHA_ = 0.4;
+const double XCPQueue::BETA_ = 0.226;
+const double XCPQueue::GAMMA_ = 0.1;
+const double XCPQueue::XCP_MAX_INTERVAL= 1.0;
+const double XCPQueue::XCP_MIN_INTERVAL= .001;
+
+const double XCPQueue::BWIDTH = 0.01;
+
+
 XCPQueue::XCPQueue(): queue_timer_(NULL), 
 estimation_control_timer_(NULL),
 rtt_timer_(NULL), effective_rtt_(0.0),
diff -ru ns-allinone-2.28.orig/ns-2.28/xcp/xcpq.h ns-allinone-2.28/ns-2.28/xcp/xcpq.h
--- ns-allinone-2.28.orig/ns-2.28/xcp/xcpq.h 2005-02-03 13:29:20.000000000 -0500
+++ ns-allinone-2.28/ns-2.28/xcp/xcpq.h 2005-06-13 18:10:36.000000000 -0400
@@ -113,11 +113,11 @@
 XCPTimer* rtt_timer_;
 double link_capacity_bps_;
 
- static const double ALPHA_ = 0.4;
- static const double BETA_ = 0.226;
- static const double GAMMA_ = 0.1;
- static const double XCP_MAX_INTERVAL= 1.0;
- static const double XCP_MIN_INTERVAL= .001;
+ static const double ALPHA_ ;
+ static const double BETA_ ;
+ static const double GAMMA_ ;
+ static const double XCP_MAX_INTERVAL;
+ static const double XCP_MIN_INTERVAL;
 
 double Te_; // control interval
 double Tq_; 
@@ -141,7 +141,7 @@
 double b_[BSIZE];
 double t_[BSIZE];
 int maxb_;alter
- static const double BWIDTH = 0.01;
+ static const double BWIDTH;
 int min_queue_ci_;
 int max_queue_ci_;
 

Solution for another problem when install ns-2.28 in Debian
./configure: line 7068: ` OSF*)' tcl8.3.2 configuration failed! Exiting .

The problem is that there are superfluous "'" characters in unix/configure:
grep in unix/configure for /etc/.relid and change it 
from 
 system=MP-RAS-`awk '{print }' /etc/.relid'`
to
 system=MP-RAS-`awk '{print }' /etc/.relid`

There are more occurrences of that line in tcl, tk and 
octcl with the same problem.

For gcc 4.1.1 or above, there is a lot of coding violations. The best way is to still use gcc-4.0 to compile, change Makefile:

CC      = gcc-4.0
CPP     = g++-4.0

Install ns-2.27 in Red Hat Linux

Follow the following steps to install ns-2.27 in Red Hat Linux distribution: 
  1. tar -xzf *
  2. ./install
  3. Change .bash_profile and add some environment variables. put /home/zhibinwu/ns-allinone-2.27/bin:/home/zhibinwu/ns-allinone-2.27/tcl8.4.5/unix:/home/zhibinwu/ns-allinone-2.27/tk8.4.5/unix into your PATH environment; so that you'll be able to run itm/tclsh/wish/xgraph.
    IMPORTANT NOTICES:
    (1) You MUST put /home/zhibinwu/ns-allinone-2.27/otcl-1.8, /home/zhibinwu/ns-allinone-2.27/lib into your LD_LIBRARY_PATH environment variable.
     If it complains about X libraries, add path to your X libraries into LD_LIBRARY_PATH.
     If you are using csh, you can set it like:
     setenv LD_LIBRARY_PATH .... If you are using sh, you can set it like:
     export LD_LIBRARY_PATH=....
    
    (2) You MUST put /home/zhibinwu/ns-allinone-2.27/tcl8.4.5/library into your TCL_LIBRARY environmental variable. Otherwise ns/nam will complain during startup.
    
    (3) [OPTIONAL] To save disk space, you can now delete directories tcl8.4.5
     and tk8.4.5. They are now installed under /home/zhibinwu/ns-allinone-2.27/{bin,include,lib}
    so , finally the bash_profile is like this:
    PATH=$PATH:$HOME/bin:/home/zhibinwu/ns2/ns-allinone-2.27/bin:/home/zhibinwu/ns2/ns-allinone-2.27/tcl8.4.5/unix:/home/zhibinwu/ns2/ns-allinone-2.27/tk8.4.5/unix
    
    export LD_LIBRARY_PATH=/home/zhibinwu/ns2/ns-allinone-2.27/otcl-1.8:home/zhibinwu/ns2/ns-allinone-2.27/lib
    
    export TCL_LIBRARY=/home/zhibinwu/ns2/ns-allinone-2.27/tcl8.4.5/library
    
  4. cd ns-2.27; ./validate

Note: The ns installation needs x-develop package. Otherwise, it will fail to build TCL TK.

Installation: A possible problem with CPP_NAMESPACE 
ns-2.27/indep-utils/cmu-scen-gen/setdest/Makefile,
 ns-2.27/indep-utils/webtrace-conv/nlanr/Makefile, and
 ns-2.27/indep-utils/webtrace-conv/dec/Makefile,
 needed to be modified in order to fix a bug in ISI's distribution. The bug
 caused a compile-time error that looked like this:

 g++ -c -Dstand_alone -DSTL_NAMESPACE=@STL_NAMESPACE@ -o setdest.o setdest.cc
 In file included from ../../../config.h:54,
 from setdest.h:5,
 from setdest.cc:57:
 ../../../autoconf.h:85: Error: namespace `CPP_NAMESPACE' undeclared
 setdest.cc:71:1: warning: "INFINITY" redefined
 In file included from /usr/include/math.h:40,
 from setdest.cc:43:
 /usr/include/bits/mathdef.h:35:1: warning: this is the location of the previous definition
 make[1]: *** [setdest.o] Error 1
 make[1]: Leaving directory `/home/iandow/netsim/ns-allinone-2.27/ns-2.27/indep-utils/cmu-scen-gen/setdest'
 make[1]: Entering directory `/home/iandow/netsim/ns-allinone-2.27/ns-2.27/indep-utils/webtrace-conv/dec'

 To fix the bug, edit ns-2.27/indep-utils/cmu-scen-gen/setdest/Makefile and 
 change this line:
 DEFINE = -Dstand_alone -DSTL_NAMESPACE=@STL_NAMESPACE@
 to this line:
 DEFINE = -Dstand_alone -DSTL_NAMESPACE=@STL_NAMESPACE@ -DCPP_NAMESPACE=std

 In the other two makefiles, append -DCPP_NAMESPACE=std to CFLAGS.


REFERENCES:

[1] The Network Simulator - ns-2, http://www.isi.edu/nsnam/ns/
[2] NS news database, http://www.isi.edu/nsnam/htdig/search.html